Request Service

 

 

The author is making a number of great points on How to Install a Bathtub Yourself in general in this content in the next paragraphs.

Installing a bathtub isn't specifically rocket science, yet it does call for solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old tub is readily accessible, the task can relocate immediately; if you need to open a wall to remove the old tub and also place the brand-new tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will require an assistant to leave the old tub as well as set in the brand-new one. See to it you have qualified on your own for the work as well as are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed task, it is far better to think about employing one prior to you begin. Chances are you might require an expert plumber to make tube links.
This post will aid you mount a new bathtub in your washroom if you have already acquired a new tub and also don't require to alter the arrangement of your previous water pipelines.
Your tools and also material checklist must make up the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Planning for the Installation

To start with, the supporting structure supplied with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps system to prevent pressure on the tub.
Fit the adaptable faucet connectors to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its final setting.

 

 

Removing Old Touches

If you require to replace old taps with new ones as a part of your installment, after that the first thing you should do is detach the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of eliminating the existing taps can be rather bothersome due to the restricted accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. As soon as the supply pipes have been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Prior to carrying on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

 

 

Setting up the Tub

Utilizing the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the bathtub till the level checks out level.
To install faucets, fit all-time low of the outermost versatile tap adapter to the ideal supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the water system as well as check all joints and brand-new pipework for leaks and tighten them if needed. Fill up the bathtub as well as additionally inspect the overflow outlet and also the typical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and securing around the bath tub must wait till the tub has been made use of a minimum of once as this will certainly settle it right into its last position.

 

 

Suitable New Taps

If the tails of the brand-new faucets are plastic, then you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Protect the faucet in position with the manufacturer supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The previous type should be linked to the tap ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Tub

In the area where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a stiff seal, creating the water to penetrate the wall in between the bath as well as the tiling, bring about complications with moisture and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes as well as cartridges, and also can sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to enable the activity experienced when the bathtub remains in use. The sealant can break relatively very early if you do not take into account this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof glue and also grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

We are very drawn to A Step-by-Step Guide to Installing a Bathtub and I am assuming you enjoyed the entire article. Sharing is nice. You never know, you may very well be helping someone out. We thank you for reading our article about How to Install a Bathtub.

Call Us Today